Forum Home - Machines, Equipment and Supplies



Goto Page:

First || 1 , 2 , 3 , 4 , 5 , 6 ... || Last

Threads: New Thread
04/05/11 New power supply. Need some input. [2]
04/05/11 starbrite reds? [6]
03/31/11 Is it just me? [8]
03/30/11 Magenta? [5]
03/29/11 healing Red Ink [6]
03/28/11 voltage [4]
03/27/11 Flash Sketch book [1]
03/27/11 Flash Sketch book [1]
03/27/11 Machine tuning resources [7]
03/24/11 Need some Waverly advice [2]
03/18/11 Can needles dull during a tattoo [13]
03/18/11 paco rollins semi mag [13]
03/18/11 Machine losing power [2]
03/18/11 Looking for a good RED [21]
03/18/11 Bugpins for color [7]
03/18/11 Tension gage / no tension gage ? [33]
03/18/11 Forums seem so quiet... [7]
03/18/11 new Eikon power supply [20]
03/16/11 Lucky's twist n lock grips [4]
03/16/11 New Tattoo Machine Design [54]
03/11/11 Needlerunners? [7]
03/09/11 Bugpins? [6]
03/08/11 wrath tubes? [7]
01/31/11 Large Mag Disposable Recommendations? [2]
01/26/11 Large Mag Disposable Recommendations? [1]
01/23/11 t-tech [3]
01/22/11 Tattoo removal cream [1]
01/21/11 Arm Rests? [7]
01/13/11 Aptek Power supply [4]
01/11/11 next generation machine with 13 mags question [12]
01/09/11 Tebori Tools [2]
01/04/11 RCA conversion project help [27]
01/04/11 Dr. Bronners body balm [4]
01/01/11 machine with o-ring vs machine without o-ring [14]
01/01/11 fusion greywash series [1]
01/01/11 @BLACK Ink CHARTS@ [3]
12/31/10 Heavier disposable [5]
12/29/10 Best Rotary Tattoo Machine [3]
12/29/10 Next Gen. one piece frame Eclipse? [3]
12/28/10 Blacklight Ink...hrm [12]

Goto Page:

First || 1 , 2 , 3 , 4 , 5 , 6 ... || Last

 
Help !!

Posted by clever thoughts from IP: 173.3.101.173 on 07/07/11
, ny United States - website


Hi, I need a better way to file the front coil core to get a flat hit. I'm so sick of wasting time trying to do this, i get it but takes a while to get it perfect. Do you guys get a perfect flat hit or close enough. Please lets throw some ideas at me and others who would like to know a better way of doing this. Thanks , hopefully there are some who are machine smart.



Reply to This Thread  
Create New Thread Topic Main Page

Replies:

RE:Help !!

Posted by will from IP: 74.240.249.170 on 07/10/11
gallatin, tn United States - website


You can by sanding cloth, like that used in gunsmithing. Put it under the amature bar while it is depressed (or perhaps only slightly melancholy) and pull it out, after doing this a few times, you'll notice that you're getting a much more flush strike. If you cut your own springs, you'll notice that many times everything else is perfect but the damn spring might twist slightly, for some guys this is a deal breaker, for some not. The machine will definitely run smoother the closer you get your tolerances on such things as spring compression, coil clearance, and the like. Luck to you.


top of page

Reply to This Thread  
Create New Thread Message Board Main Page