Forum Home - Machines, Equipment and Supplies



Goto Page:

1 , 2 , 3 , 4 , 5 , 6 ... || Last

Threads: New Thread
02/17/16 Fake Starbrite Inks [40]
11/23/13 5 Flat Pencil Tip Needles [1]
09/10/13 Custom Springs? [6]
07/15/13 Best Black ink??? [4]
07/02/13 How Do Lab Grade Power Supplies Compare to Eikon, [1]
07/02/13 How Do Lab Grade Power Supplies Compare to Eikon, [1]
07/02/13 How Do Lab Grade Power Supplies Compare to Eikon, [1]
05/23/13 tuning tattoo machine [32]
05/13/13 10uf cap? [2]
05/13/13 Dotwork [5]
05/13/13 A-bar modify [2]
05/13/13 Capacitor Question [9]
03/04/13 Cheyenne Hawk Bugpins (not really?) [1]
02/22/13 machine cuts out after long use... [10]
01/23/13 Tattoo removal cream [8]
01/10/13 Color packingwith curved mags [18]
09/11/12 cx-2 supply [1]
09/03/12 Speed vs Force [10]
08/31/12 Attn: Coil builders.. re: wire [4]
08/30/12 fk iron galaxie 2 [1]
08/21/12 Littte machine but good machine Liner !??! [1]
08/14/12 follow thru & stl% [2]
07/01/12 B&G machine [7]
06/25/12 lining ink [4]
06/25/12 Rubber band Question [8]
06/25/12 stl/ follow through question [4]
06/25/12 Zeroing out follow through [26]
06/24/12 cheyenne hawk [19]
06/24/12 crtical wireless foot switch [11]
06/24/12 front spring [2]
06/15/12 workhorse irons aaron cain, [18]
06/10/12 newagetattoosupply.com [3]
04/05/12 Humbly Seeking Advice [4]
01/14/12 changed to 8 wraps, now machine needs more voltage [15]
01/14/12 Kuro Sumi Soft Graywash [4]
01/14/12 Fantasia Tattoo Ink? [3]
12/09/11 Luckys Power Supplies [1]
11/11/11 Starting fresh again [3]
11/08/11 New Company : ROTARY & COILS [1]
11/06/11 1/4 Phono v.s RCA Jack [3]

Goto Page:

1 , 2 , 3 , 4 , 5 , 6 ... || Last

 
Dotwork

Posted by Roumen from IP: 205.207.90.222 on 07/08/12
mississauga, on Canada - website


What are some good coil machines that run slow enough for doing dotwork. I'm not a big fan of rotaries, and was wondering if there is a way to slow a coil machine down to that level.



Reply to This Thread  
Create New Thread Topic Main Page

Replies:

slow down dc machine

Posted by Mystic from IP: 210.185.11.111 on 07/10/12
Napier, Hawkes Bay New Zealand - website


you will need to go to a very long, soft front spring and have very big throw, the only to slow D.C. down without loosing hitting power.


top of page
dot work

Posted by Jerry San Martin from IP: 97.90.0.219 on 07/21/12
South El Monte , Ca United States - website


You should really consider using the HYPER rotary from stigma it can be slowed down considerably and the hit adjusted for coloring. Its a fine machine and in my humble opinion would work great for what you're looking for. Also, check out my website for more tattoo info: www.SanMartinTattoo.com


top of page
RE:Dotwork

Posted by Sascha Schneider from IP: 212.166.63.125 on 01/28/13
Lontzen, DG Belgium - website


I'm not a pro, so don't take my word (haven't done this in real - pure theory)...
there are different vids on youtube where people do dotwork with coil machines ...
dot for dot ... soft spring, lower volt ...
but Jerry is right, if you wanna tattoo in kinda one trace you should consider a rotary with long stroke (f.e. the stigma's, hummingbird ...) and low volt


top of page
RE:Dotwork

Posted by dagat from IP: 222.127.224.234 on 05/13/13
cebu, cebu Philipines - website


47uf machine on slow volts in cooperate of bronze contact screw to reach the tip point of long standard soft frontspring /18gauge.; if not enough higher your capacitor on next uf value.


top of page

Reply to This Thread  
Create New Thread Message Board Main Page